Tehnike popravka automobila Land Rover Discovery 3

Auto u radionici
When working on a vehicle in the workshop always make sure that: Where practicable, the parking brake is applied and the wheels are securely chocked to prevent the vehicle moving forwards or...

Akumulatorska baterija
OPREZ: Neophodno je da prođe 10 minuta nakon odspajanja akumulatora prije bilo kakvog rada na bilo kojem dijelu SRS sustava. UPOZORENJE: Prije provođenja bilo kakvih postupaka koji uključuju...

Pokretanje motora automobila
UPOZORENJE: Iako se ne preporučuje pokretanje vozila pomoću pomoćnog motora, poznato je da bi to povremeno mogao biti jedini praktičan način pokretanja vozila. Treba se obratiti na sljedeće i također...

Vuča automobila
OPREZ: Kada je vuča neophodna, potrebno je uputiti na odjeljak o podizanju, dizanju i vuči u ovom priručniku. Kada se vozilo vuče, kontakt brava mora biti u položaju II (steering lock released and...

Opće upute za instalaciju
Component removal Whenever possible, clean components and the surrounding area before removal. Blank off openings exposed by component removal. Following disconnection, seal fuel, oil or hydraulic...

Opći pregled komponenti
All components should be inspected for wear or damage before reassembling. Always ensure that component to be inspected is clean and free from oil or grease. When a component is to be checked...

Uređaji za zaključavanje
Always replace locking devices with one of the same design and of the correct size. Tab washers . Always release locking tabs before loosening fixings, do not re-use tab washers. Locknuts . Always...

Oznake vijaka i matica
An ISO metric bolt or screw made of steel and larger than 6 mm in diameter can be identified by either of the symbols ISO M or M embossed or indented on top of the bolt head. In addition to marks...

Kuglični i valjkasti ležajevi
When removing and installing bearings, ensure that the following practices are observed to ensure component serviceability: UPOZORENJE: Servisni alati razvijeni su za uklanjanje većine ležajeva;...

Hidraulički kočioni sustav
Brake Pads and Linings Always fit the correct grade and specification of brake pads and linings. When replacing these items, always replace as complete axle sets. Brake Hydraulics Always observe the...

Fleksibilne cijevi i crijeva
When removing or installing flexible hydraulic pipes and hoses, ensure that the following procedures are observed to ensure component serviceability: Prior to removal, clean area around hose or pipe...

Crijeva i stezaljke sustava goriva
Fuel system hoses Some fuel hoses are made up of two laminations, an armoured rubber outer sleeve and an inner viton core. Whenever a hose is removed, ensure that the inner bore is inspected to check...

Orijentacija i spajanje crijeva
Correct orientation of cooling system hoses is important to ensure that hoses do not become fatigued or damaged through contact with adjacent components. Where orientation marks are provided on the...

Mjere opreza pri radu s električnom opremom
General The following guidelines are intended to ensure the safety of the operator whilst preventing damage to the electrical and electronic components of this vehicle. Equipment Prior to commencing...

Mjere opreza pri rukovanju gorivom
The following information lists basic precautions which must be observed if fuel is to be handled safely. It also outlines other areas of risk which must not be ignored. As this information is issued...

Uljne brtve
Always renew oil seals which have been removed either as an individual component or as part of an assembly. Never use a seal which has been improperly stored or handled. Take great care when removing...

Sigurnosne mjere pri radu sa sustavom osobne zaštite (SRS)
OPREZ: Ne postavljajte dječje sjedalice okrenute unatrag na suvozačevo sjedalo. The SRS contains components which are potentially hazardous to service personnel if not handled correctly. The...

Pregled senzora udara
After any degree of side or frontal body damage, inspect the impact crash sensors. Replace a crash sensor if there is any sign of damage. UPOZORENJE: Budite posebno oprezni kada lakirate ili...

Aktivacija zračnog jastuka i zatezača sigurnosnog pojasa
OPREZ: Tijekom aktiviranja dijelovi modula zračnog jastuka postaju dovoljno vrući da vas opeku. Pričekajte 30 minuta nakon aktiviranja prije dodirivanja modula zračnog jastuka. Deployment procedures...

Zamjena SRS komponenti
UPOZORENJE: Kontrolni modul zaštitne opreme (RCM) will log a crash fault after every impact which is severe enough to cause airbag deployment. It is possible to have three crashes/impacts logged...

Aktiviranje prednjeg zračnog jastuka
UPOZORENJE: Ako su prednji zračni jastuci aktivirani, sljedeće komponente moraju se zamijeniti: Driver airbag module Passenger airbag module Fly leads (where applicable) connecting front airbag...

Aktiviranje bočnog zračnog jastuka
UPOZORENJE: Ako se bočne zračne zavjese aktiviraju, sljedeće komponente moraju se zamijeniti na strani vozila na kojoj je došlo do aktiviranja: Side curtain airbag Any side impact sensors that have...

Moduli zračnih zavjesa
UPOZORENJE: Ako su moduli zračnih jastuka za glavu aktivirani, sljedeće komponente moraju se zamijeniti na strani vozila na kojoj je došlo do aktiviranja: Head airbag modules Link lead between airbag...

Sudar automobila straga
UPOZORENJE: Ako se zatezači sigurnosnih pojaseva aktiviraju tijekom stražnjeg sudara, potrebno je zamijeniti sljedeće komponente: Seat belt pre-tensioners Front and rear seat belt retractors used...

Mjere opreza za klima uređaj
The A/C system contains fluids and components which could be potentially hazardous to the service engineer or the environment if not serviced and handled correctly. The following guidelines are...