Brake system of the car Range Rover 3

Front brake disc wear and runout check
Examination 1. Raise the front of the car. WARNING: Do not work under a vehicle raised only on a jack or lift. Always install safety props. 2. Remove the front wheel. 3. Remove the two screws...

Checking wear and runout of the rear brake disc
Examination 1. Raise the rear of the vehicle. WARNING: Do not work under a vehicle raised only on a jack or lift. Always install safety props. 2. Remove the wheel. 3. Remove the two screws securing...

Removal of air from the brake system
Bleeding the brake system can be performed according to the procedure using the Testbook/r4 diagnostic tool or manually as described below. Examination 1. The procedure under consideration refers to...

Parking brake adjustment
Examination 1. Lapping the rear parking brake pads WARNING: Where possible, road tests should be carried out on dry, hard pavement. Always obey speed limits and local traffic regulations. 2. Verify...

Brake disc front brakes
Dismantling 1. Raise the front of the car. WARNING: Do not work under a vehicle raised only on a jack or lift. Always install safety props. 2. Remove the wheel. 3. Remove the two screws securing the...

Brake disc rear brakes
Dismantling 1. Raise the rear of the vehicle. WARNING: Do not work under a vehicle raised only on a jack or lift. Always install safety props. 2. Remove the wheel. 3. Remove the two screws securing...

Pre-pressure pump
Dismantling 1. Remove the front wheel arch liner. EXTERIOR PARTS, REPAIR WORKS, Fender liner - front wheel arch. 2. Remove the nut securing the siren to the bracket and move the siren to the side. 3....

Brake reservoir
Dismantling 1. Install a container to collect escaping brake fluid. CAUTION: Brake fluid can damage paintwork. If brake fluid comes into contact with painted surfaces, remove any traces of fluid...

Brake master cylinder — tandem
Dismantling 1. Remove the brake reservoir. BRAKE SYSTEM, REPAIR WORKS, Brake reservoir. 2. Disconnect the brake lines. CAUTION: Always plug fittings and openings to keep dirt out of the system. 3....

Brake Pedal Assembly
Dismantling 1. Remove the panel covering the brake pedal assembly. VEHICLE INTERIOR PARTS, REPAIR WORKS, Control panel lower shield - passenger side. 2. Remove the protective shield. CAR INTERIOR...

Lever assy parking brake
Dismantling 1. Remove the center console. CAR INTERIOR PARTS, REPAIR WORKS, Center console. 2. Loosen and remove the air box. 3. Release the clamps and disconnect the parking brake cables from the...

Parking brake cables
Dismantling 1. Put the car on a lift. 2. Remove the brake disc. BRAKING SYSTEM, REPAIR WORKS, Brake disc - rear brake mechanisms. 3. Remove the upper return spring of the parking brake pads. 4....

Parking brake alarm switch
Dismantling 1. Remove the center console. CAR INTERIOR PARTS, REPAIR WORKS, Center console. 2. Remove the screw securing the switch. 3. Disconnect the cable from the switch. 4. Remove the switch....

Brake pads front brake mechanisms
WARNING: In order not to reduce the effectiveness of the brake system, the brake pads must be replaced simultaneously on the brakes of both front wheels. If the pad wear indicator turns on, replace...

Rear brake pads
CAUTION: In order not to reduce the effectiveness of the brake system, the brake pads must be replaced simultaneously on the brakes of both rear wheels. If the pad wear indicator turns on, replace...

The wear sensor of the pads of the front of the car
Dismantling 1. Raise the front of the car on one side. WARNING: Do not work under a vehicle raised only on a jack or lift. Always install safety props. 2. Remove the left front wheel. 3. Open the...

The wear sensor of the pads of the rear of the car
Dismantling 1. Raise the rear of the vehicle on one side. WARNING: Do not work under a vehicle raised only on a jack or lift. Always install safety props. 2. Remove the rear right wheel. 3. Turn out...

Rear brake drum brake pads
Dismantling 1. Raise the rear of the vehicle. WARNING: Do not work under a vehicle raised only on a jack or lift. Always install safety props. 2. Remove rear wheels. 3. Remove the brake disc. BRAKING...

Pneumatic booster assembly
Dismantling 1. Remove the cover covering the units in the engine compartment 2. Remove the main brake cylinder. BRAKING SYSTEM, REPAIR WORKS, Brake master cylinder - tandem. 3. Disconnect the vacuum...

Vacuum pump TD6
Before disconnecting the battery, make sure that all the requirements and conditions contained in the section on disconnecting the battery are met. GENERAL INFORMATION, Precautions when working with...

ABS electronic control unit
If the ECM needs to be replaced, connect the Testbook/T4 diagnostic tool for the correct sequence before disconnecting the battery. Before disconnecting the battery, make sure that all the...

ABS front wheel speed sensor
Dismantling 1. Raise the front of the car on one side. WARNING: Do not work under a vehicle raised only on a jack or lift. Always install safety props. 2. Remove the front wheel. 3. Open the cover...

Rear wheel speed sensor
Dismantling 1. Raise the rear of the vehicle on one side. WARNING: Do not work under a vehicle raised only on a jack or lift. Always install safety props. 2. Remove the rear wheel. 3. Turn out 5...

ABS pressure regulator block
Dismantling 1. Release the retainer and disconnect the ABS pressure regulator connector block. 2. Disconnect the block from the sensor. 3. Place a cloth under the pressure regulator to avoid...

ABS pressure regulator pressure sensor
Dismantling 1. Place a cloth under the pressure regulator to avoid splashing brake fluid. CAUTION: Brake fluid can damage paintwork. If brake fluid comes into contact with painted surfaces, remove...

Dynamic stabilization sensor
Dismantling 1. Remove the casing of the center console. CAR INTERIOR PARTS, REPAIR WORKS, Cladding - center console. 2. Loosen and remove the air box. 3. Turn out 2 screws of fastening of the gauge...