Vehicle fuel supply Land Rover Freelander 2

Fuel System Specification
Detail Specifications Maximum constant flow 160 l/h Maximum flow in the engine 40 l/h Maximum return flow 90 l/h Maximum return line pressure 0.7 bar Minimum engine pressure 0.5 bar Minimum filter...

Description of the fuel system
Pos. spare part no Name 1 - Common fuel manifold 2 - High pressure pipeline - from the fuel manifold to the nozzle (4 things.) 3 - High pressure pipeline - from the pump to the fuel manifold 4 -...

High pressure fuel pump
Pos. spare part no Name A - Fuel supply line from filter to suction pump B - Low pressure fuel return to filter C - High pressure fuel supply to the fuel manifold 1 - High pressure plunger pairs (3...

Common rail fuel manifold
Pos. spare part no Name A - Low pressure fuel return to filter B - High pressure fuel supply - from the high pressure fuel pump to the fuel manifold C - High pressure pipeline - from the fuel...

Fuel injectors
Pos. spare part no Name 1 - High pressure fuel supply from the fuel manifold 2 - Low pressure fuel return to filter 3 - Electrical connection on ECM 4 - 10 digit injector code These four fuel...

High pressure fuel lines
The high pressure fuel lines are connected between the high pressure pump and the fuel manifold and between the fuel manifold and the four injectors. The pipes are short in length to maintain the...

Inspection and testing of the fuel system
CAUTION: Diagnosis by substituting a component from another vehicle is NOT allowed. The substitution of control units does not guarantee confirmation of the fault and, moreover, may cause additional...

Table of fault signs
Symptom Possible reason Action Engine cranks but won't start Fuel level Fuel contamination Leaks/blockages in the fuel system Air intake system Electronic engine controls Check fuel level and fuel...

Dtc fault code index
NOTE: If a control module/component is suspected and the vehicle continues to be covered by the manufacturer's warranty, refer to the warranty manual before installing a new module (subsection B1.2),...

Removal and installation of a fuel nozzle
Avoid open source of flame, sparks or flammable substances. After stopping the engine, wait at least one minute before starting any repairs to the fuel injection system. Clean the area around the...

Removal and installation of the fuel manifold
Avoid open source of flame, sparks or flammable substances. After stopping the engine, wait at least one minute before starting any repairs to the fuel injection system. Clean the area around the...

Removal and installation of the fuel pump
Avoid open source of flame, sparks or flammable substances. After stopping the engine, wait at least one minute before starting any repairs to the fuel injection system. Clean the area around the...

Throttle body
Removing 1. Remove the cover and disconnect the ground wire from the battery. Refer to procedure: Specifications (414-00 Charging system - General information, Specifications). 2. Remove the engine...

Turbocharger specification
General Specification of Turbocharger Position Specification Type variable resistance Pressure at 2000 rpm 1.1 bar Pressure at 3000 rpm 1.2 bar Torque Specifications Description Nm lb-ft catalytic...

Description of the turbocharger
Pos. spare part no Name A - Air intake from the air filter B - Compressed air to charge air cooler C - Exhaust gas intake D - Exhaust gas outlet 1 - Oil supply line 2 - Compressor housing 3 -...

Working principle of a turbocharger
The turbocharger uses the energy of the exhaust gas flow from the engine to provide compressed air to the air intake system. Adjustable vanes allow the turbocharger to generate the required boost...

Turbocharger drive rod
NOTE: The steps in this procedure may be part of the installation procedure. NOTE: The illustrations may differ in some details, but the fundamental points are completely true. Removing 1. Raise and...

Removal and installation of a turbocharger
WARNING: Use caution when working near hot exhaust system components. Removing 1. Raise the vehicle. WARNING: Place secure stands under the vehicle. 2. Remove the EGR heat exchanger (EGR). Refer to...
There is 2 commentary