Car steering Land Rover Freelander 2

Steering specification
Detail Specifications Manufacturer/type Power steering rack and pinion Number of turns from one extreme position to another 2,58 Piston diameter 44 mm (1,73 in) Gear rack diameter 28 mm (1,10 in)...

Inspection and verification
1. Visually inspect for obvious signs of damage and system integrity. Mechanical factors: Check the correct tire pressure, size and tread pattern Check for tire and wheel rim damage Check wheel...

Table of fault signs
NOTE: If a component is suspected and the vehicle continues to be covered by the manufacturer's warranty, refer to the warranty manual before installing a new component (subsection B1.2), or...

Bleeding air from the power steering system
1. Clean the power steering reservoir around the filler cap and fluid indicator. 2. Check the power steering fluid: if there are air bubbles in it, wait for the air to escape and add the recommended...

Flushing the power steering system
NOTE: If the steering is sluggish or there is contamination in the power steering system, the system flush procedure should be followed as detailed below. If any items have been replaced in the power...

Power Steering Specification
Lubricants, fluids, sealants and adhesives Detail Specification Volume Recommended Fluid Pentozin CHF202 Fill up to the maximum mark on the tank General specification Detail Specifications PAS pump -...

Description of power steering
Location of elements - TD4 diesel engine NOTE: Right hand drive option shown (RH), for left-hand drive version (LH) likewise Pos. spare part no Name 1 - Suction hose - from tank to pump 2 - Tank 3 -...

Steering Gear Description
Steering gear Pos. spare part no Name 1 - Lock-nut 2 - Tie rod end 3 - Lock-nut 4 - Tie Rod 5 - Steering gear cover 6 - Elements of fastening of the case of the steering mechanism. 7 -...

Steering Valve Block Description
NOTE: Typical valve block shown Pos. spare part no Name 1 - Rail 2 - gear shaft 3 - Outer sleeve 4 - oil sleeve 5 - mud seal 6 - input shaft 7 - Torsion 8 - Retaining ring 9 - Oil seal 10 - PTFE ring...

Power Steering Pump Description
Power Steering Pump - TD4 Pos. spare part no Name 1 - Injection outlet (to steering valve block) 2 - Pulley 3 - suction port (from the tank) A variable displacement vane pump supplies the required...

Description of the steering fluid reservoir
Pos. spare part no Name 1 - Lid 2 -Frame 3 - Return connection (DW12 - from the steering gear) (i6 - from the working fluid cooler) 4 - suction connection (from the power steering pump) 5 - Bracket...

Fluid cooler (i6 only)
Pos. spare part no Name 1 - Fluid return line (from the steering gear) 2 - Tank 3 - Fluid return line (from the working fluid cooler) 4 - suction hose (from the power steering pump) 5 - Fluid cooler...

The principle of operation of the hydraulic booster
Schematic representation of a typical fixed volume pump: Pos. spare part no Name 1 - Tank 2 - Fluid cooler 3 - valve block 4 - Steering rack and pinion 5 - Flow control/pressure relief - return line...

Checking the pressure in the hydraulic booster circuit 2.2L Duratorq — TD4
Special tool 211-011-01 Valve Block, Power Steering Pressure Test 211-011-02 Hose, Power Steering Pressure Test 211-011-12 Adapter, Power Steering Pressure Test 211-287 Hose and Gauge, Power Steering...

Power Steering Pump 2.2L Duratorq — Td4
Removing 1. Remove the engine cover. Refer to Procedure: Engine Cover - 2.2L Duratorq - Td4 (501-05 Interior trim, Removal and installation). CAUTION: Be sure to plug all open connections to prevent...

Removal and installation of the steering mechanism
Removing 1. Raise and support the vehicle. WARNING: Place secure stands under the vehicle. 2. Remove the front wheels. Refer to procedure: Wheel and tire (204-04 Wheels and tires, Removal and...

Power Steering Working Fluid Cooler
Removing 1. Raise and support the vehicle. WARNING: Do not work on or under a vehicle supported only by a jack. Be sure to install reliable supports under the car. 2. Remove the front wheels complete...

Power Steering Reservoir
Removing 1. Remove the power steering reservoir cap. 2. Using a suitable syringe, remove the working fluid from the power steering reservoir. 3. Remove the power steering reservoir. Prepare to...

Description and principle of operation of the steering gear
Torque specification Description Nm lb-ft Tie rod end nut 70 52 Tie rod end locknut 55 41 Location of elements Pos. spare part no Name 1 - ball joint 2 - Lock-nut 3 - Tie rod end 4 - Lock-nut 5 - Tie...

Thrust tip
Special tool 205-754 Splitter, Ball Joints Removing 1. Raise and support the vehicle. WARNING: It is forbidden to carry out work on a vehicle standing on only one jack. Always place the vehicle on...

Steering gear cover
Removing 1. Raise and support the vehicle. WARNING: Place secure stands under the vehicle. 2. Remove the tie rod end. Refer to Procedure: Rod End (211-03 Steering gear, Removal and installation). 3....