NOTE: This procedure includes the removal and installation of both rear seatbacks and the left rear seatback upholstery. Removal and installation of an upholstery of a back of the right back seat is carried out similarly. To avoid damage to the rear seatbacks, the procedure must be followed strictly in accordance with all notes and cautions.
Removing
1.
2.
3. Release the right rear seatback outer hinge pin bushing.
4. Use a screwdriver to release the lock lever on the outer pivot pin bushing.
5.
- Release the right rear seatback outer hinge pin bushing from the support bracket.
- Detach the right rear seat back from the left rear seat back.
CAUTION: The left rear seatback inner hinge pin has annular grooves. When removing the right backrest from the left, be careful not to damage the inner hinge bushing of the right seat.
6. Remove and discard the right rear seatback outer pivot pin bushing.
7.
- Remove the armrest, if equipped.
- Remove and discard the armrest pivot bushing spring clips.
8.
- Slide the armrest up.
- Slide the armrest out.
9.
- Remove the armrest base plate.
- Remove and discard 4 Christmas clips.
10. Establish the holder of a tape of a seat belt.
WARNING: Make sure the seat belt holder is installed at least 200 mm from the belt stop in the direction of the rear center seat belt tensioner.
11. Turn out a nut of the lower element of fastening of a back central seat belt.
12.
13.
14. Release the bushing of the outer pivot pin of the left rear seat backrest.
15. Use a screwdriver to release the lock lever on the outer pivot pin bushing.
16.
- Release the left rear seatback outer hinge pin bushing from the support bracket.
- Carefully slide the left rear seatback inner hinge pin out of the center hinge pin.
CAUTION: The left rear seatback inner hinge pin has annular grooves. Be careful not to damage the center pivot bushing.
17. Remove and discard the left rear seatback outer hinge pin bushing.
18.
19. Remove the panel of finishing of the central seat belt.
20. Remove the panel of finishing of the blocking button of a back of a back seat.
21.
- Using a screwdriver, press the locking tab.
- Pull the tube guide up.
- Remove and discard the head restraint tube rails.
22. Disconnect the rear seatback upholstery from the backrest frame.
23. Remove the rear seat back upholstery and padding assembly from the rear seat back lock button.
24. Release the rear center seat belt and lower belt anchorage from the backrest upholstery.
25. Remove an upholstery and stuffing of a back of a back seat.
26. Remove and discard bent rings.
Installation
1. Use pliers to install wire rings.
NOTE: If installing new rear seatback upholstery, cut holes in the backrest for the headrest tubular guides and center seat belt trim panel. Use «old» back upholstery as a template. This also applies to the foam back padding.
NOTE: Use pliers to close the wire rings. Do not use any other tools. It is required to close the wire rings with an overlap, as shown in the figure.
NOTE: Use new wire rings.
2. Pass the rear center seat belt and the lower belt anchor through the backrest upholstery.
3. Install the rear seat back upholstery and padding.
4. Attach the rear seatback upholstery and padding assembly near the rear seatback lock button.
5. Attach the rear seat back upholstery to the rear seat back frame.
6. Install new head restraint guide tubes.
7. Establish the panel of finishing of the blocking button of a back of a back seat.
8. Install the center seat belt trim panel.
9. Install the headrests.
10. Install a new left rear seatback outer hinge pin bushing. Tightening torque: 35 Nm
11.
- Install the left rear seatback inner hinge pin into the center hinge pin.
- Carefully lower the left rear seatback outer hinge pin bushing into the support bracket.
If there is excessive wear or damage, the center pivot bush must be replaced.
The inner pivot pin of the left rear seatback has annular grooves. Be careful not to damage the center pivot bushing.
12. Install a new bolt into the outer pivot pin bushing stop arm. Tightening torque: 23 Nm
13. Establish the removable panel of furnish of the left back lateral part of salon.
14. Fasten the lower element of fastening of a back central seat belt. Tightening torque: 40 Nm
15. Remove the holder of a tape of a seat belt.
WARNING: Check the correct operation of the rear center seat belt pretensioner.
16. If installing with armrest, install new armrest pivot bushing spring clips.
WARNING: New armrest pivot bushing spring clips must be installed. Failure to follow these instructions may result in injury.
17. Install 4 new Christmas tree clips in the armrest base plate.
18. Install the armrest base plate.
19. Install the armrest.
NOTE: Make sure the spring clips of the armrest pivot are in the grooves of the armrest pivot.
20. Install a new right rear seatback outer hinge pin bushing. Tightening torque: 35 Nm
21. Install the service pad into the right rear seat backrest inner pivot sleeve.
CAUTION: If a used right rear seatback is installed, the condition of the inner hinge bushing must be checked and a service pad installed. If excessive damage is found to the inner pivot sleeve, the right rear seat back frame must be replaced.
NOTE: This step is not required if a new right rear seatback is being installed.
22.
- Carefully slide the right rear seatback inner hinge pin onto the left rear seatback inner hinge pin.
- Carefully lower the right rear seatback outer hinge pin bushing into the support bracket.
CAUTION: The left rear seatback inner hinge pin has annular grooves. When installing the right backrest, be careful not to damage the inner pivot sleeve.
23. Install a new bolt into the locking arm of the outer pivot pin bushing. Tightening torque: 23 Nm
24. Establish the removable panel of furnish of the right back lateral part of salon.
Comments on this article