KV6 engine fuel system Freelander 1

Throttle control cable — check and adjustment
Examination 1. Remove the soundproof casing of the engine. KV6 ENGINE - MODIFICATION K, Camshafts of the left cylinder head, Noise-insulating casing of the engine. 2. Before adjusting the cable,...

Relieve Fuel System Pressure: Except Americas
Examination 1. Remove the acoustic cover. KV6 ENGINE - MODIFICATION K, Camshafts of the left cylinder head, Noise-insulating casing of the engine. 2. Lay a rag near the fuel supply hose to prevent...

Fuel System Pressure Relief: Americas
Examination 1. Remove the acoustic cover. KV6 ENGINE - MODIFICATION K, Camshafts of the left cylinder head, Noise-insulating casing of the engine. 2. Prior to May 2003: Remove the nut and bolt...

Measurement of pressure in the fuel supply system: except for the Americas
Examination 1. Remove the soundproof casing of the engine. KV6 ENGINE - MODIFICATION K, Camshafts of the left cylinder head, Noise-insulating casing of the engine. 2. Lay a rag near the fuel supply...

Measuring pressure in the fuel supply system: Americas
Dismantling 1. Remove the acoustic cover. KV6 ENGINE - MODIFICATION K, Camshafts of the left cylinder head, Noise-insulating casing of the engine. 2. Lay a fuel soaking cloth under the fuel rail....

Air filter filter element
Dismantling 1. Remove the acoustic cover. KV6 ENGINE - MODIFICATION K, Camshafts of the left cylinder head, Noise-insulating casing of the engine. 2. Unscrew the 2 screws securing the filter element...

Air Filter Element: Americas
Dismantling 1. Remove the acoustic cover. KV6 ENGINE - MODIFICATION K, Camshafts of the left cylinder head, Noise-insulating casing of the engine. 2. Remove the 2 bolts securing the heat shield to...

Throttle control cable — removal and installation
Dismantling 1. Remove the soundproof casing of the engine. KV6 ENGINE - MODIFICATION K, Camshafts of the left cylinder head, Noise-insulating casing of the engine. 2. Release the throttle cable from...

Front Left Oxygen Sensor: Except Americas
Dismantling 1. Raise the front of the vehicle. WARNING: Do not work under a vehicle that is only supported by a jack. Always install safety props. 2. Remove the lower engine protection. EXTERIOR...

Front left oxygen sensor: Americas
Dismantling 1. Disconnect "negative" battery terminal. 2. Remove a noise-insulating casing of the engine. KV6 ENGINE - MODIFICATION K, Camshafts of the left cylinder head, Noise-insulating casing of...

Front right oxygen sensor: Except Americas
Dismantling 1. Raise the front of the car. WARNING: Do not work under a vehicle that is only supported by a jack. Always install safety props. 2. Remove the left front wheel. 3. Remove the right...

Front right oxygen sensor: Americas
Dismantling 1. Disconnect "negative" battery terminal. 2. Remove a noise-insulating casing of the engine. KV6 ENGINE - MODIFICATION K, Camshafts of the left cylinder head, Noise-insulating casing of...

Throttle: Except Americas
Dismantling 1. Disconnect "negative" battery terminal. 2. Remove a noise-insulating casing of the engine. KV6 ENGINE - MODIFICATION K, Camshafts of the left cylinder head, Noise-insulating casing of...

Throttle: Americas
Dismantling 1. Disconnect "negative" battery terminal. 2. Remove a noise-insulating casing of the engine. KV6 ENGINE - MODIFICATION K, Camshafts of the left cylinder head, Noise-insulating casing of...

Electric motor of the valve drive of the reconfigurable intake system
The procedure described also applies to the high power damper motor. Dismantling 1. Disconnect "negative" battery terminal. 2. Remove a noise-insulating casing of the engine. KV6 ENGINE -...

Rear left oxygen sensor: Except Americas
Dismantling 1. Raise the front of the car. WARNING: Do not work under a vehicle that is only supported by a jack. Always install safety props. 2. Remove a head of the selector of an automatic...

Rear Left Oxygen Sensor: Americas
Dismantling 1. Disconnect "negative" battery terminal. 2. Raise the front of the vehicle and install safety stands. WARNING: Do not work under a vehicle that is only supported by a jack. Always...

Rear right oxygen sensor: Except Americas
Dismantling 1. Disconnect "negative" battery terminal. 2. Raise the vehicle on a four post lift. 3. Disconnect the heated oxygen sensor harness from the mounting brackets. 4. Loosen and disconnect...

Fuel Rail: Except Americas
Dismantling 1. Disconnect "negative" battery terminal. 2. Remove the inlet receiver. MANIFOLDS AND EXHAUST SYSTEM: MOD. K, move. V6, REPAIRS, Intake reservoir seals: vehicles manufactured before May...

Fuel Rail: Americas
Dismantling 1. Disconnect "negative" battery terminal. 2. Remove the inlet receiver. MANIFOLDS AND EXHAUST SYSTEM: MOD. K, move. V6, REPAIRS, Intake reservoir seals: vehicles manufactured before May...

Nozzle — removal and installation
Dismantling 1. Disconnect "negative" battery terminal. 2. Remove the fuel rail. PETROL FUEL SUPPLY, ADJUSTMENTS, Fuel rail, KV6 engine: Except North American market. PETROL ENGINE FUEL SUPPLY,...

Cruise control actuator: except Americas
Dismantling 1. Disconnect "negative" battery terminal. 2. Remove a noise-insulating casing of the engine. KV6 ENGINE - MODIFICATION K, Camshafts of the left cylinder head, Noise-insulating casing of...

Cruise Control Vacuum Pump: Except Americas
Dismantling 1. Remove the battery tray. SYSTEM OF STARTING THE ENGINE AND CHARGING THE BATTERY, REPAIR WORKS, Support tray - storage battery. 2. Release the 3 rubber pads securing the vacuum pump to...

Cruise Control Switch: Before May 2004
Dismantling 1. Remove the radio. ENTERTAINMENT SYSTEMS, REPAIRS, Radio receiver - models up to 04MY. 2. Remove the interior heating control knobs. 3. Turn away 2 screws of fastening of an overlay of...

Cruise control controller
Dismantling 1. Move the right front seat fully forward. 2. Loosen the 2 screws securing the controller cover. 3. Remove the cover. 4. Remove the controller interface from the bracket and set it...

Cruise controller interface
Dismantling 1. Move the right front seat fully forward. 2. Loosen the 2 screws securing the controller cover. 3. Remove the cover. 4. Remove the interface box from the bracket, disconnect the...