K1.8 engine fuel system Land Rover Freelander 1

Throttle control cable — check and adjustment
Examination 1. Before adjusting the cable, check that it is routed and secured correctly. Adjustment 1. Remove the throttle cable adjusting nut from the bracket. 2. Hold the damper drive section in...

Depressurizing the fuel supply system
Examination 1. Lay a rag near the fuel supply hose to prevent spilled fuel from spreading. CAUTION: Fuel leakage is inevitable during this operation. Take safety precautions to prevent fire or...

Measurement of pressure in the fuel supply system
Examination 1. Disconnect "negative" battery terminal. 2. Place a rag under the fuel pipe to collect spilled fuel. CAUTION: Fuel leakage is inevitable during this operation. Take safety precautions...

Draining the fuel tank
Operating procedure 1. Disconnect both terminals on the battery, first of all "negative" terminal. 2. Remove the fuel priming pump. FUEL SUPPLY SYSTEM OF PETROL ENGINE, ADJUSTMENTS, Electric fuel...

Air purification filter
Dismantling 1. Disconnect the air hose from the air filter housing. 2. Turn away a collar and disconnect an air hose from a throttle branch pipe. 3. Turn away 2 bolts of fastening of the case of the...

Air filter filter element
Dismantling 1. Unfasten the 4 fasteners securing the top cover of the air filter housing. 2. Release the cover and slide it to the side. 3. Remove the air filter element. Installation 1. Remove dirt...

Inertial fuel cut-off switch
Dismantling 1. Disconnect the connector from the inertial switch. 2. Turn away a bolt of fastening of an arm of the inertial switch to a bulkhead panel. 3. Remove the inertial switch from the...

Front oxygen sensor
Dismantling 1. Loosen and disconnect the oxygen sensor connector. 2. Release the oxygen sensor harness from the clamp on the cylinder block. 3. Using a special 22 mm wrench, unscrew the oxygen...

Mass air flow sensor (MAF)
North American market countries. Dismantling 1. Disconnect "negative" battery terminal. 2. Remove a noise-insulating casing of the engine. KV6 ENGINE - MODIFICATION K, Camshafts of the left cylinder...

Fuel pump relay
Dismantling 1. Remove the cover from the fuse box in the passenger compartment. 2. Locate and remove the fuel priming pump relay. Installation 1. Insert the relay. 2. Install the cover on the fuse...

Throttle pipe
Dismantling 1. Disconnect "negative" battery terminal. 2. Turn away a collar and disconnect an air hose from a throttle branch pipe. 3. Unfasten the 4 latches and remove the air filter cover. 4....

Rear oxygen sensor
Dismantling 1. Raise the front of the car. WARNING: Do not work under a vehicle that is only supported by a jack. Always install safety props. 2. Loosen the fasteners securing the shift lever boot to...

Main fuel filter
Dismantling 1. Disconnect "negative" battery terminal. 2. Remove the fuel level sensor. INSTRUMENTS, REPAIR WORKS, Gauge - fuel gauge. 3. Disconnect the 2 connectors from the top of the fuel pump...

Electric fuel pump — removal and installation
CAUTION: If there is a lot of fuel in the tank, then pump it out through the filler neck, using a special device, to a level below the fuel inlet. Dismantling 1. Disconnect "negative" battery...

Fuel tank: except for North American market
Dismantling 1. Place the car on a lift. 2. Disconnect "negative" battery terminal. 3. Remove the fuel pump module. FUEL SUPPLY SYSTEM OF PETROL ENGINE, ADJUSTMENTS, Electric fuel pump. CAUTION: Fuel...

Fuel Tank: North American Market Countries
Dismantling 1. Place the car on a lift. 2. Disconnect "negative" battery terminal. 3. Using the tool, transfer the fuel from the fuel tank to a hermetically sealed container. For detailed...

Filler pipe — removal and installation
Dismantling 1. Disconnect "negative" battery terminal. 2. Check that there is less than half the fuel level in the tank. If there is more fuel, then drain it so that less than half the level remains....

Nozzles (set) — removal and installation
Dismantling 1. Disconnect "negative" battery terminal. 2. Loosen the clamp and remove the vacuum hose from the fuel pressure regulator. 3. Remove the dipstick. 4. Lay a fuel soaking cloth under the...

Resume switch: from May 2004
Dismantling 1. Release the 2 fastening buttons and remove the switch cover from the control panel. 2. Turn away 2 screws of fastening of a support of the switch to the panel of devices. 3. Remove the...

Multifunction switch
Dismantling 1. Remove the airbag module from the steering wheel. PASSIVE SAFETY SYSTEMS, REPAIR WORK, Driver airbag. 2. Release the cruise control wires from the clamps and disconnect the connector....