Engine management system MEMS Land Rover Freelander 1
Spark plug
Dismantling 1. Remove ignition coils. ENGINE MANAGEMENT SYSTEM: MEMS, REPAIRS, Ignition Coil. 2. Wipe the area around the spark plugs. 3. Using a 16mm socket, remove the 4 spark plugs. Installation...
Dismantling 1. Remove ignition coils. ENGINE MANAGEMENT SYSTEM: MEMS, REPAIRS, Ignition Coil. 2. Wipe the area around the spark plugs. 3. Using a 16mm socket, remove the 4 spark plugs. Installation...
Ignition coil
Dismantling 1. Disconnect "negative" battery terminal. 2. Turn away 3 bolts of fastening of a cover of coils of ignition. 3. Remove the cover. 4. Disconnect the high voltage wire from the spark plug....
Dismantling 1. Disconnect "negative" battery terminal. 2. Turn away 3 bolts of fastening of a cover of coils of ignition. 3. Remove the cover. 4. Disconnect the high voltage wire from the spark plug....
Engine Control Module (ECM)
Block for implementing ignition and fuel supply strategies. Dismantling 1. Disconnect "negative" battery terminal. 2. Remove the 5 screws securing the junction box cover. 3. Turn away 2 bolts of...
Block for implementing ignition and fuel supply strategies. Dismantling 1. Disconnect "negative" battery terminal. 2. Remove the 5 screws securing the junction box cover. 3. Turn away 2 bolts of...
Idle Air Control (IAC)
Dismantling 1. Disconnect "negative" battery terminal. 2. Disconnect the connector from the idle speed controller. 3. Disconnect the bypass air hose from the idle speed control and remove it from the...
Dismantling 1. Disconnect "negative" battery terminal. 2. Disconnect the connector from the idle speed controller. 3. Disconnect the bypass air hose from the idle speed control and remove it from the...
Sensors: Coolant Temperature Sensor (ECT)
Dismantling 1. Disconnect the block from the coolant temperature sensor. 2. Install a container to collect the escaping coolant. 3. Remove the coolant temperature sensor. Installation 1. Clean the...
Dismantling 1. Disconnect the block from the coolant temperature sensor. 2. Install a container to collect the escaping coolant. 3. Remove the coolant temperature sensor. Installation 1. Clean the...
Sensors: crankshaft position (CKP) sensor
Dismantling 1. Disconnect the block from the crankshaft position sensor (CKP). 2. Turn away a bolt of fastening of the gauge of provision of a cranked shaft. 3. Remove the crankshaft position sensor....
Dismantling 1. Disconnect the block from the crankshaft position sensor (CKP). 2. Turn away a bolt of fastening of the gauge of provision of a cranked shaft. 3. Remove the crankshaft position sensor....
Throttle position sensor
Dismantling 1. Disconnect "negative" battery terminal. 2. Disconnect the bypass air hose from the idle speed control and remove it from the throttle pipe. 3. Disconnect the connector from the...
Dismantling 1. Disconnect "negative" battery terminal. 2. Disconnect the bypass air hose from the idle speed control and remove it from the throttle pipe. 3. Disconnect the connector from the...
Sensors: Camshaft position sensor (CMP)
Dismantling 1. Disconnect "negative" battery terminal. 3. Release the camshaft position sensor harness connector from the bracket and disconnect the connector. 4. Release the sensor harness from the...
Dismantling 1. Disconnect "negative" battery terminal. 3. Release the camshaft position sensor harness connector from the bracket and disconnect the connector. 4. Release the sensor harness from the...
Pedal Position Sensor
Dismantling 1. Remove the 2 nuts securing the pedal assembly to the bulkhead. 2. Disconnect the gas cable from the gas pedal. 3. Disconnect the connector from the pedal position switch. 4. Remove the...
Dismantling 1. Remove the 2 nuts securing the pedal assembly to the bulkhead. 2. Disconnect the gas cable from the gas pedal. 3. Disconnect the connector from the pedal position switch. 4. Remove the...
Manifold absolute pressure (MAP) sensor
Dismantling 1. Remove the cover and disconnect the connector from the absolute pressure sensor on the intake manifold (MAP). 2. Turn away 2 screws of fastening of the gauge of absolute pressure to an...
Dismantling 1. Remove the cover and disconnect the connector from the absolute pressure sensor on the intake manifold (MAP). 2. Turn away 2 screws of fastening of the gauge of absolute pressure to an...
This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian