Gasoline engine K1.8 car Land Rover Freelander 1

Oil pressure check
1. Turn out the contact gauge of pressure of oil. ENGINE - MODIFICATION K, volume 1.8, Front oil seal of the exhaust camshaft, Contact oil pressure sensor. 2. Add oil if necessary. MAINTENANCE,...

Front exhaust camshaft oil seal
Replacing the oil seal on the intake camshaft is done in the same way. Dismantling 1. Disconnect "negative" battery terminal. 2. Remove the lower engine protection. EXTERIOR PARTS, REPAIR WORKS,...

Rear exhaust camshaft oil seal
Dismantling 1. Disconnect "negative" battery terminal. 2. Remove the air cleaning filter. FUEL SUPPLY OF PETROL ENGINE, REGULATIONS, Air filter, K1.8 engine. 3. Lay out a rag to collect the leaking...

Rear intake camshaft oil seal
Dismantling 1. Disconnect "negative" battery terminal. 2. Remove the air cleaning filter. FUEL SUPPLY OF PETROL ENGINE, REGULATIONS, Air filter, K1.8 engine. 3. Lay out a rag to collect the leaking...

Integral camshaft cover: sealing
Integral camshaft cover: sealing and replacing oil seals. Dismantling 1. Remove the rear timing belt cover. ENGINE - MODIFICATION K, volume 1.8, Front exhaust camshaft oil seal, Rear timing belt...

Replacing connecting rod bearings
Dismantling 1. Disconnect "negative" battery terminal. 2. Remove the cylinder head. ENGINE - MODIFICATION K, displacement 1.8, Front exhaust camshaft oil seal, Cylinder head gasket. 3. Remove the...

Crankshaft pulley
Dismantling 1. Disconnect "negative" battery terminal. 2. Remove the accessory drive belt. ENGINE START AND BATTERY CHARGING SYSTEM, REPAIR WORK, Attachment drive belt - K1.8 engine without air...

Front crankshaft oil seal
Dismantling 1. Remove the timing belt. ENGINE - MODIFICATION K, volume 1.8, Front oil seal of the exhaust camshaft, Timing belt. 2. Remove the crankshaft drive gear. 3. Install the stop LRT-37-010 on...

Rear crankshaft oil seal
Dismantling 1. Remove the flywheel. ENGINE - MODIFICATION K, volume 1.8, Front oil seal of the exhaust camshaft, Flywheel. 2. Using a flat-blade screwdriver that does not have sharp burrs, remove the...

Cylinder head gasket
Dismantling 1. Disconnect "negative" battery terminal. 2. Remove the rear timing belt cover. ENGINE - MODIFICATION K, volume 1.8, Front exhaust camshaft oil seal, Rear timing belt cover. 3. Turn away...

Valve cover gasket
Dismantling 1. Disconnect "negative" battery terminal. 2. Loosen the 2 clamps and disconnect the crankcase ventilation hose from the valve cover. 3. Remove ignition coils. ENGINE MANAGEMENT SYSTEM:...

Oil scraper caps — removal and installation
Dismantling 1. Disconnect "negative" battery terminal. 2. Remove camshafts. ENGINE - MODIFICATION K, volume 1.8, Front exhaust camshaft oil seal, Integral camshaft cover: sealing and replacement of...

Engine and gearbox
Dismantling 1. Disconnect "negative" battery terminal. 2. Remove the hood. EXTERIOR PARTS, REPAIR WORKS, Bonnet. 3. Drain the engine coolant. COOLING SYSTEM: MODIFICATION K, volume 1.8, ADJUSTMENTS,...

Arm of the right support of the engine assy
Dismantling 1. Remove the lower engine protection. EXTERIOR PARTS, REPAIR WORKS, Engine lower shield. 2. Turn out a bolt of fastening of the top right cross-beam of the engine to the top bracket on...

Engine hydraulic mount, right
Dismantling 1. Disconnect "negative" battery terminal. 2. Remove the right engine bracket. ENGINE - MODIFICATION K, volume 1.8, Front oil seal of the exhaust camshaft, Bracket of the right engine...

Flywheel — removal and installation
Dismantling 1. Remove the clutch assembly. CLUTCH, REPAIRS, Clutch Assembly/Driven Plate and Clutch Release Bearing (clutch release) - K1.8. 2. Loosen but do not remove the 6 flywheel mounting bolts....

Oil pump — removal and installation
Dismantling 1. Remove the timing belt. ENGINE - MODIFICATION K, volume 1.8, Front oil seal of the exhaust camshaft, Timing belt. 2. Remove the crankshaft drive gear. 3. Turn away 2 bolts of fastening...

Oil pan sealing
Dismantling 1. Remove a reception pipe of system of release. MANIFOLDS AND EXHAUST SYSTEM: MOD. K, volume 1.8, REPAIR WORKS, Downpipe. 2. Drain the engine oil. MAINTENANCE, MAINTENANCE, Engine oil...

Oil pressure switch
Dismantling 1. Disconnect "negative" battery terminal. 2. Raise the front of the vehicle. WARNING: Do not work under a vehicle that is only supported by a jack. Always install safety props. 3. Turn...

Reducing valve of the lubrication system
Dismantling 1. Remove the lower part of the front timing belt cover. ENGINE - MODIFICATION K, volume 1.8, Front exhaust camshaft oil seal, Lower part of the front timing belt cover: vehicles without...

Oil temperature sensor
Dismantling 1. Disconnect "negative" battery terminal. 2. Raise the front of the vehicle. WARNING: Do not work under a vehicle that is only supported by a jack. Always install safety props. 3. Turn...

Timing belt — removal and installation
Dismantling 1. Disconnect "negative" battery terminal. 2. Remove the hydraulic support. ENGINE - MODIFICATION K, volume 1.8, Front seal of the exhaust camshaft, Right engine hydraulic support. 3....

Top Timing Cover
Dismantling 1. Disconnect "negative" battery terminal. 2. Loosen the lower bolt securing the upper timing belt cover. 3. Turn away 5 bolts of fastening of the top cover to a back cover. 4. Remove the...

Rear Timing Belt Cover
Dismantling 1. Remove the timing belt. ENGINE - MODIFICATION K, volume 1.8, Front oil seal of the exhaust camshaft, Timing belt. 2. Remove the gear alignment tool LRT-12-134. 3. Mark the gears so...

Lower part of the front timing belt cover: without air conditioning
Dismantling 1. Disconnect "negative" battery terminal. 2. Remove the top part of the timing belt cover. ENGINE - MODIFICATION K, volume 1.8, Front oil seal of the exhaust camshaft, Upper timing...

Lower part of the front timing belt cover: with air conditioning
Dismantling 1. Disconnect "negative" battery terminal. 2. Remove the top part of the timing belt cover. ENGINE - MODIFICATION K, volume 1.8, Front oil seal of the exhaust camshaft, Upper timing...