| Threaded connection | In the SI system | In Pound Feet |
| Screws securing the compressed air cooler to the chassis | ||
| - Lower | 10 N.m | 7.5 lb-ft |
| - Upper | 5 N.m | 3.5 lb-ft |
| Screws for fastening the fan casing to the compressed air cooler radiator | 5 N.m | 3.5 lb-ft |
| Screws of fastening of the electric motor of the fan to a casing | 5 N.m | 3.5 lb-ft |
| Air cooler connector bracket nut | 10 N.m | 7.5 lb-ft |
| cooler pipe nuts | 25 N.m | 18 lb-ft |
| crankshaft position sensor (CKP) | 9 N.m | 7 lb-ft |
| Screw securing the cover to the gearbox housing | 10 N.m | 7.5 lb-ft |
| Screws of fastening of a leading disk to the hydrotransformer | 45 N.m | 33 lb-ft |
| Conductor fixing screw "masses" to gearbox | 25 N.m | 18 lb-ft |
| Screws for fastening the fuel heat exchanger to the bracket (KV6 engine) | 25 N.m | 18 lb-ft |
| Screws of fastening of an arm of the heat exchanger of fuel (KV6 engine) | ||
| - M8 | 25 N.m | 18 lb-ft |
| - M12 | 85 N.m | 63 lb-ft |
| Fuel heat exchanger fastening screws (Td4 engine) | ||
| - 2 screws | 45 N.m | 33 lb-ft |
| - 1 screw | 25 N.m | 18 lb-ft |
| Fastening the heat exchanger hoses to the gearbox | 18 N.m | 13 lb-ft |
| Unions of hoses of the heat exchanger of working liquid | 18 N.m | 13 lb-ft |
| Gearbox pan screws * + | 7 N.m | 5 lb-ft |
| Gearbox cover screw (Td4 engine) | 10 N.m | 7.5 lb-ft |
| Gearbox drain plug | 45 N.m | 33 lb-ft |
| Control plug of a transmission | 14 N.m | 10 lb-ft |
| Fastening the pallet to the gearbox housing | 85 N.m | 63 lb-ft |
| Screws of fastening of a transmission to the engine | 85 N.m | 63 lb-ft |
| Gearbox support screws | 85 N.m | 63 lb-ft |
| Transmission through screw | 100 N.m | 74 lb-ft |
| Inhibitor Switch Screws | 3 N.m | 2.2 lb-ft |
| Intermediate reduction coolant hose retainer screw | 25 N.m | 18 lb-ft |
| Intermediate Reduction Mount Bracket Screws * (KV6 engine) | 50 N.m | 37 lb-ft |
| Screws of fastening of an arm of a support of an intermediate reduction gear to a forward support of the engine * (KV6 engine) | 50 N.m | 37 lb-ft |
| Screws for fastening the bracket of the intermediate reduction gear support to the pallet * (KV6 engine) | 45 N.m | 33 lb-ft |
| Screws of fastening of an intermediate reduction gear to a transmission (KV6 engine) | 80 N.m | 59 lb-ft |
| Attaching the Heat Shield of the Manifold to the Bracket intermediate downshift (KV6 engine) | ||
| - Bolts | 9 N.m | 7 lb-ft |
| - nuts | 45 N.m | 33 lb-ft |
| Nut of fastening of a heat-reflecting shield of a collector to a case of transfer (KV6 engine) | 25 N.m | 18 lb-ft |
| Gear selector housing nuts | 10 N.m | 7.5 lb-ft |
| Selector cable nut | 6 N.m | 4.5 lb-ft |
| Nut of fastening of the lever of the selector to a shaft of the selector of a transmission | 25 N.m | 18 lb-ft |
| Screws for fastening the starter to the gearbox housing | 45 N.m | 33 lb-ft |
| Torque Converter Inspection Port Screws | 9 N.m | 7 lb-ft |
* Tighten consistently.
+ Apply sealant, part no. STC 4600 to the threads.
Comments on this article