Vehicle lighting and headlights Land Rover Defender 90/110/130

Description and principle of operation of outdoor lighting
Location of elements Models since MY 2007 (except for SVX model (60th anniversary) Pos. spare no Name 1 parts Emergency light button 2 - Fog lamp control unit 3 - Rear fog lamp 4 - Tail/brake light 5...

Headlight adjustment
General procedures 1. NOTE: Check high beam adjustment using special equipment. If it is missing, headlight alignment can be temporarily checked and adjusted as follows. Park the unladen vehicle with...

Headlight assembly — removal and installation
Removing 1. Unscrew 4 screws and disconnect from a wing lanterns of marker lights and indexes of turn. 2. Disconnect electric sockets and remove lanterns of dimensional fires and indexes of turn. 3....

Side marker light
Removing NOTE: This procedure describes how to remove and install the side turn signal. 1. Press the diffuser firmly to the right. 2. Lift the left end and remove the canopy from the fender. 3. Turn...

Upper brake light
Removing 1. Open the back door. 2. Unscrew 2 screws and remove a cover from the top stoplight. 3. Remove the insulating coating from the connector, release the latches and undock the connectors,...

Stoplight switch
Removing 1. Remove the brake light switch cover. 2. Disconnect the plug connectors. 3. Remove stoplight switches. Installation 1. CAUTION: Make sure the brake pedal is at rest, not depressed, or...

Headlight switch — removal and installation
Removing 1. Remove the steering column covers. For more information, see the chapter: Steering column shrouds (501-05 Interior trim, Removal and installation). 2. Disconnect the electrical connector....

Rear light assembly
Removing 1. Remove 2 screws securing the rear light to the body. 2. Disconnect the electrical connector and remove the lamp. Installation 1. Install the tail light and dock the connector. 2. Screw in...

Side turn signal lamp
Removing 1. Remove 2 screws securing the side turn signal light. 2. Disconnect the electrical connector and remove the lamp. Installation 1. Establish a lantern of the lateral index of turn and join...

Rear fog lamp
Removing NOTE: This procedure describes the removal and installation of the reversing light and rear fog light. 1. Remove the two screws together with the sealing washers and remove the diffuser from...

License plate lamp
Removing 1. Remove one screw securing the lamp cover and reflector to the socket. 2. Remove the lamp (s) from the cartridge. Installation 1. Install a new lamp (s). 2. Install reflector and lamp...

License plate lighting
Removing 1. Remove one screw and remove the lamp cover and diffuser. 2. Unscrew the 2 latches and remove the metal cover to access the lamp latches and wiring. 3. Disconnect the lamp wires from the...

Headlight beam leveling switch
Removing 1. Disconnect the wire "masses" from the battery. For more information, see the chapter: Disconnecting and connecting the battery (414-01 Battery, Battery Mount and Wires, General...

Reversing light switch
Removing 1. Remove the floor console. For more information, see the chapter: Floor Console (501-12 Instrument panel and console, Removal and installation). 2. Re-lay the left carpet. 3. Release the...

Reversing lamp
Removing NOTE: This procedure describes the removal and installation of the reversing light and rear fog light. 1. Working from under the vehicle, remove the protective cover and disconnect the...

Headlight range control motor
Removing 1. Remove headlight assembly. For more information, please refer to chapter: Headlight assembly (417-01 Outdoor lighting, Removal and installation). 2. Disconnect the headlamp leveling motor...

Description and principle of interior lighting
Location of elements NOTE: Left hand drive vehicle shown (LHD), a similar device has a car with right-hand drive (RHD). Pos. spare part no Name 1 - Switch right (RH) back door (if installed) 2 -...

Interior lamp bulb
Removing 1. Remove the diffuser from the lamp. 2. Separate the contacts of the lamp holder and remove the lamp. Installation 1. Spread the contacts of the lamp socket and install the lamp. 2. Install...

Interior lamp
Removing 1. Remove the diffuser from the cover. 2. Remove the two nuts that secure the light to the headlining and the support bracket on the roof. 3. Remove the cover from the support bracket studs...