Steering geometry
| Steering wheel diameter | 412 mm (16,22 in) |
| Front wheel alignment | Negative toe -10'±10' |
| Rear wheel alignment | Positive convergence +5'±15' |
| Camber - Front wheels | -10' ± 45' |
| Camber - Rear wheels | -10' ± 45' |
| The angle of the longitudinal inclination of the axis of rotation of the wheel | 3° 15' ± 45' |
| Pitch angle difference between left and right sides | 1°maximum |
| Front camber difference between left and right side | 1°maximum |
| Rear wheel camber difference | 1°maximum |
| Deviation of the kingpin - with a stable suspension position | 7°Tested with the vehicle on level ground, with its own weight in accordance with the EEC standard. Rock the front of the car up and down until it reaches its normal static position. |
Turn circle between curbs
| Models 90 | |
| Tires 265/75x16 | 12,65 m (41,5 ft) |
| All other tires | 11,70 m (38,4 ft) |
| Models 110 | |
| Tires 750 x 16 | 13,41 m (44 ft) |
| Models 130 | |
| Tires 750 x 16 | 15,24 m (50 ft) |
Steering housing and pump
| Make and type of steering housing | Adwest Varamatic - worm and roller |
| Steering ratio | Adjustable: Straight - 19.3:1 Locked - 14.3:1 |
| The number of turns of the steering wheel from lock to lock | 3,375 |
| Make and type of steering pump | JTekt P4 |
Power steering system
| Working fluids and filling volumes | |
| Power steering fluid | Texaco Cold Climate 33270 |
| Filling volume - steering mechanism and reservoir - left-hand drive | 2.90 l |
| Filling volume - steering mechanism and reservoir - right-hand drive | 3.40 l |
Tightening torques
| Description | Nm | lbf/ft |
| Longitudinal tie rod to steering arm | 40 | 30 |
| Ball Nuts | 40 | 30 |
| Clamp bolt (M6) | 9 | 7 |
| Steering column bracket nuts | 22 | 16 |
| steering wheel nut | 43 | 32 |
| Primary tightening torque of the trailing arm to support nut | 80 | 60 |
| Final tightening torque of the trailing arm to support nut | 110 | 80 |
| Universal joint pinch bolt | 30 | 22 |
| Steering adjuster locknut | 60 | 45 |
| Steering gear nut | 175 | 130 |
| Sector shaft cover to steering gear | 75 | 55 |
| Steering gear to chassis | 80 | 60 |
| Power Steering Fluid Lines, 14mm Thread | 15 | 11 |
| Power Steering Fluid Lines, 16mm Thread | 20 | 15 |
| steering gear tie rod | 80 | 60 |
| Power steering pump high pressure line | 20 | 15 |
| Power steering pump support | 35 | 25 |
| Power steering pump pulley bolts | 10 | 7 |
| Power steering pump hose clamp | 3 | 2 |
| Power steering pump front support plate bolts | 9 | 7 |
| Power Steering Reservoir Hose Clamp | 3 | 2 |
Fastener size
| Nm | lbf/ft | |
| M5 | 6 | 4,5 |
| M6 | 9 | 7 |
| M8 | 25 | 18 |
| M10 | 45 | 33 |
| M12 | 90 | 65 |
| M14 | 105 | 77 |
| M16 | 180 | 133 |
| 1/4 in | 9 | 7 |
| 5/16 in | 24 | 18 |
| 3/8 in | 39 | 29 |
| 7/16 in | 78 | 58 |
| 1/2 inch | 90 | 65 |
| 5/8 in | 135 | 100 |
The tightening torque specifications in the preceding table apply to all screws and bolts used, except as specifically noted in the table.
Comments on this article